您好!歡迎訪問廣州艾欣科學儀器有限公司網站!
          全國服務咨詢熱線:

          13724099587

          當前位置:首頁 > 資料下載 > EPA1664—己烷提取物的檢測

          EPA1664—己烷提取物的檢測

          發布時間:2013/6/23      點擊次數:8301

           1) Assemble

          a) Assemble cartridge adapters on the vacuum manifold

          b) Place ECUNIOGXF cartridge(s) on each vacuum station needed

          c) Connect the manifold to a suitable trap and attach the trap to a vacuum system capable of

          attaining a minimum of 25” Hg (635 mm) of vacuum

          d) Insert waste collection vial in manifold (optional)

          2) Prepare Water Sample

          a) Adjust the pH of the sample to less than 2 by adding 5 mL of 6N HCl or 2.5 mL of concentrated

          H2SO4

          b) If acid was added to the sample in the field do not add more unless the pH is greater than 2

          Gloves are recommended as skin oils may affect final sample weight

          3) Condition the Cartridge

          a) Rinse sides of cartridge and bottle holder with 10 mL of hexane

          b) Allow cartridge to soak for 1 minute

          c) Draw the hexane through the cartridge using vacuum

          d) Discard the hexane from waste vial

          e) Draw full vacuum through the cartridge for 2 minutes to dry

          f) Add 10 mL of methanol to the cartridge

          g) Slowly draw the methanol through leaving a layer on the cartridge frit

          h) Soak for one minute

          i) Remove waste vial and discard methanol

          From this point on do not let the cartridge dry out otherwise repeat at step f)

          j) Add 30 mL of DI water to the cartridge

          k) Draw the water through the cartridge to waste

          4) Sample Addition

          a) Add the 1 liter water sample directly to the cartridge

          b) Draw the sample through the cartridge under low vacuum. This may take several minutes

          depending on the solids in the sample. (Note 1) Increase vacuum pressure if necessary. Do

          not exceed 500 mL/minute

          c) Remove the cartridge and tap any excess water from the bottom of the cartridge

          d) Replace cartridge and allow to dry under full vacuum for 10 minutes

          e) Remove any water remaining in the bottom support of the cartridge with a paper towel if

          necessary

          5) Elution

          a) Prepare an extract collection vial containing about 8 mm (0.3 inch) of anhydrous sodium

          sulfate

          b) Place the vial in the manifold station under the cartridge

          c) Rinse the water sample bottle with 10 mL of hexane

          d) Add the hexane to the cartridge

          e) Soak cartridge for 2 minutes

          f) Turn on vacuum and slowly draw the hexane through the cartridge and into the collection vial

          g) Turn off vacuum then repeat steps 5 c) – f) 2 additional times but use 10 mL of hexane

          h) Do not allow the solvent to splash into the collection vial

          i) Add another 10 mL of hexane to the cartridge, rinsing the bottle holder

          j) Soak cartridge for 2 minutes

          k) Draw the hexane through the cartridge

          6) Dry the Extract

          a) Remove the collection vial from the manifold and cover with a screw cap

          b) Shake the extract to form a water/hexane emulsion and immediay pour the extract through a

          sodium sulfate funnel or column containing approximay 40 g of anhydrous sodium sulfate

          held in place with a glass wool plug or frit. Do not use filter paper

          c) Collect the extract in a clean, pre-weighed vessel

          d) Rinse the collection vial with hexane and add it to the sodium sulfate. This will rinse the vial

          and the sodium sulfatez

          7) Gravimetric analysis

          a) Carefully evaporate the hexane using a TurboVap® or similar evaporator at 40° C until the

          extract just reaches dryness.

          Note: Do not over dry or low recoveries will result

          Do not dry on a hot plate or in an oven or over dry as low recoveries may result

          b) Allow to cool to room temperature in a desiccator before weighing

          c) Record this weight as the mass per unit volume of oil and grease and report as HEM as mg/L

          Notes

          1) If very high solids are present, add glass wool to the cartridge prior to extraction to prevent clogging and improve

          flow. The glass wool must be thoroughly rinsed as part of the cartridge during the elution step.

          2) Stearic acid must be in solution in the spiking solution or low recoveries will result. If small crystals are present in

          the spiking solution, sonicate or shake until dissolved.

          DCN-118170-


          文件下載    
          廣州艾欣科學儀器有限公司
          地址:廣東省廣州市天河區元崗街道元崗路天河慧通產業廣場A1棟六樓1604(總部)
          郵箱:fighter31668@163.com
          傳真:86-020-36536169
          關注我們
          歡迎您關注我們的微信公眾號了解更多信息:
          歡迎您關注我們的微信公眾號
          了解更多信息
          主站蜘蛛池模板: 亚洲乱码中文字幕综合| 国产呻吟久久久久久久92| 一人上面一个吃我电影| 黄瓜视频网站在线观看| 成人av电影网站| 亚洲欧美综合区自拍另类| 精品国产一区二区三区AV性色 | 欧美视频在线网站| 免费看少妇作爱视频| 中文字幕激情视频| 国外bbw免费视频| 久久96国产精品久久久| 日韩精品在线电影| 亚洲色成人网一二三区| 蜜芽.768.忘忧草二区老狼| 国产日产久久高清欧美一区| 丁香六月婷婷综合激情动漫| 束缚强制gc震动调教视频| 免费在线观看污污视频| 老司机亚洲精品影院在线| 国产精品成人99一区无码| 98精品全国免费观看视频| 散步乳栓项圈尾巴乳环小说| 嫩模bbw搡bbbb搡bbbb| 国产三级A三级三级| 9久热精品免费观看视频| 日本在线视频WWW鲁啊鲁| 亚洲欧洲日产国码久在线观看| 美女视频免费看一区二区| 国产人成视频在线视频| 麻豆成人精品国产免费| 大地资源在线资源免费观看| 久久久精品国产| 欧美日韩国产精品va| 亚洲精品成人网站在线播放 | 私人影院在线观看| 国产又色又爽又刺激在线观看 | 高中生的放荡日记h| 国产小视频在线观看网站| 97精品在线视频| 在车子颠簸中进了老师的身体|